| Signal
Channel |
|
|
|
Mode |
|
Normal or Baseline Sample, with baseline
control via output or input signal. |
|
Sensitivity |
|
±20 mV to ±2 V full scale in a 1-2-5
sequence |
|
Coupling |
|
AC/DC |
|
Impedance |
|
50 W // 10 pF
DC only
1 MW // 30 pF DC or AC |
|
Maximum Input without damage |
|
50 W: ±5 V
1 MW: ±100 V (AC coupled mode) |
|
Offset |
|
±10 × FS via 20-turn potentiometer |
|
Overload indicator |
|
LED lights for signals > 1.1 x FS |
|
Overload Recovery Time |
|
Recovers after 1 trigger for x10 overload |
|
Gain Drift |
|
0.5% /°C, gate width > 30 ns;
1.0% /°C, gate width < 10 ns |
|
DC Drift (referred to input) |
|
0.2%/°C, gate width > 20 ns;
1.0%/°C, gate width < 20 ns |
|
Bandwidth |
|
DC to 450 MHz (50 W
DC input)
DC to 100 MHz (1 MW DC input)
1.5 Hz to 100 MHz (1 MW AC input) |
|
Signal Risetime |
|
50 W input 1.7
ns; 20% to 80%
1 MW input 10 ns; 20% to 80%
(from 50 W source) |
| Timing and Control |
|
|
|
Gate width |
|
>1 ns to 30 µs in 1-3-10 sequence
switch selectable with a continuously variable ×1 to ×5 multiplier |
|
Sample Correlation |
|
Less than 0.5% of the sample output due
to trigger t remains at trigger t + 1 |
|
Delay |
|
|
|
Min Intrinsic
Delay |
|
20 ns (ECL trigger input)
15 ns (ECL trigger input, delay board bypassed) |
|
Max Delay
Range |
|
3 ns to 300 ns in 1-3-10 sequence plus
user options, which give 10 µs (default), and 1 µs, 100 µs, 1 ms
or 3 ms by capacitor change. |
|
Manual
Adjustment |
|
Screwdriver vernier control adjusts delay
from 0.5 % to 100 % of range |
|
External
Adjustment |
|
0 to 10 V DC varies delay by 0.5 % to 100
% of range |
|
Input |
|
|
|
Trigger |
|
|
|
Internal |
|
0.5 Hz to 40 kHz selectable with range
switches 0.5, 5, 50, 500, 5000, off. Vernier is 10× range. |
|
External ECL |
|
Positive edge, 5 ns min pulse width with
termination of 50 W to -2 V; -5 V to +10 V pk-pk safe
input |
|
External TTL |
|
Negative edge, 20 ns min pulse width ; -5 V
to +10 V pk-pk safe input |
|
Max. Trigger
Rate |
|
Max 80 kHz |
|
Trigger Indicator |
|
LED lights when unit is triggered |
|
Trigger Generator |
|
|
|
Output |
|
BNC TTL out on rear panel active in all
trigger modes. Polarity set by jumper. |
|
Frequency
ranges |
|
0.5, 5, 50, 500 Hz, 5 kHz and off
with vernier to overlap ranges. |
|
Baseline Input |
|
TTL line to indicate whether sample is
signal or baseline value |
| Analog Output Averager |
|
|
|
Modes |
|
Linear or Exponential |
|
Samples Averaged |
|
1, 3, 10, 30, 100, 300, 1k, 10k |
|
LSO Droop Rate |
|
< 0.2% FS/s |
|
Averager Droop Rate |
|
When there are no triggers the droop rate is < 0.001%
per minute for 10k samples |
| Outputs |
|
|
|
Average out |
|
±10 V FS with 50 W
output impedance and capable of driving a 2 kW
load |
|
Last Sample out |
|
±10 V FS |
|
Gate Monitor |
|
0.3 V into 50 W
to ground. Marker pulse-width equals gate width. Position is within
5 ns from actual gate |
|
Internal Rate Generator |
|
TTL |
|
Baseline Output |
|
TTL output line that toggles with each
trigger to indicate whether next sample will be treated as a signal
or baseline value. |
| Power |
|
+24 V at 200 mA -24 V at 150 mA |
|
|
|
+12 V at 300 mA -12 V at 590 mA |
|
|
|
+6 V at 160 mA -6 V at 630 mA |
| Dimensions |
|
|
|
Height |
|
8¾" (222 mm) |
|
Width |
|
2¾" (70 mm) |
|
Depth |
|
9¾" (248 mm) |
| Weight |
|
3 lb (1.4 kg) |
is
a trademark of AMETEK, Inc.